| Processor |
| |
CPU |
32-bit
Motorola 5407 ColdFire® Processor |
| |
Processing
Speed |
257
MIPS (Dhrystone 2.1 benchmark) |
| Memory |
| |
On-board
Memory |
36MB |
| |
Expandable
Memory |
Compact
Flash slot up to 4GB (accepts standard Type
II Compact Flash not included) |
| Y-Bus
- Crestron PAC2 Control System |
| |
40
Mb/s parallel communications; 2 slots for
Crestron's existing CNX I/O expansion cards
or new C2 expansion cards |
| Z-Bus |
| |
300Mb/s
parallel communications; 1 expansion card
slot. Optional cards include: C2ENET-1:
Single Port 10/100 BaseT Ethernet, C2ENET-2:
Dual Port WAN-LAN-10/100 BaseT Ethernet.
Future Support for USB, USBII, FireWire, or
Disc Drive Array. |
| |
Ethernet
Support |
10/100
BaseT Ethernet, Dynamic/static IP and full
duplex TCP/IP, UDP/IP, optional Firewall,
Router, Network Address Translator (NAT),
Built-in Web Server. |
| Connectors |
| |
RELAYS |
(8)
normally open, isolated relays; each relay
is rated 1A, 30VAC/DC; MOV arc suppression
across contacts for use with "real
world" loads |
| |
INPUT/OUTPUT |
(8)
programmable digital/analog input and
digital outputs; digital outputs offer 250mA
sync from maximum 24VDC; catch diodes for
use with "real world" loads;
digital inputs rated for 0-24 VDC, 20K ohms
input impedance, logic threshold 1.25VDC;
analog inputs rated 0-10VDC, protected to
24VDC maximum, 20K ohms input impedance;
programmable 2K ohms pullup resistor (per
pin, software reference to GND or closure to
GND) Crestron PAC2 Control System |
| |
Cresnet
ports |
(1)
connector on CPU card plus (8) groups of (4)
connectors on top plate (32 total); each
group is from a separate port on an internal
8-port Cresnet Expander Hub. (2) 5-position
connectors for Cresnet signals and an
additional Override contact closure signal. |
| |
Override
input |
(1)
3-position mini-phoenix connector for
external contact closure inputs (connects
directly to the 5-position Cresnet
connectors) |
| |
Cresnet
backup |
(1)
5-position connector for backup computer to
automatically take control of the Cresnet
network upon failure of the internal
computer |
| |
Computer
port |
RS-232
port on CPU card for console use. |
| Reset
Buttons |
| |
HW-R |
Performs
physical reset of system |
| |
SW-R |
Restarts
SIMPL program |
| LED
Indicators |
| |
PWR |
Indicates
power supplied to the unit |
| |
NET |
Indicates
activity within the system |
| |
ERR |
Indicates
an error message is available from the
software feature buttons |
| |
LAN
A – LNK + ACT |
Indicates
attachment to and communication over LAN
(port 1 of Z-Bus card) |
| |
LAN
B – LNK + ACT |
Indicates
attachment to and communication over LAN
(port 2 of Z-Bus card, if dual port card
inserted) |
| |
Cresnet
Activity |
(8)
LEDs indicate Cresnet segment activity |
| |
Cresnet
PWR |
(4)
LEDs indicate Cresnet power supplied to the
unit. Crestron PAC2 Control System |
| |
RUN |
Indicates
the built-in Cresnet backup processor is
operating |
| Power |
| |
Built-in
A/C to 24V, 75Wpower supply for internal
functions; (4) 3-position mini-phoenix
connectors for flexible power distribution. |
| Dimensions |
| |
3.75"
/ 9.52cm (H) x
14.00" / 35.56cm (W) x
7.40" / 18.80cm (D) |
| Weight |
| |
8.00lbs
/ 3.60kg |
