| Processor
- Crestron MP2 Mp2E Control System |
| |
CPU |
32-bit
Motorola ColdFire® Microprocessor |
| |
Processing
Speed |
257 MIPS
(Dhrystone 2.1 benchmark) |
| Memory |
| |
4MB
Flash, 32MB SDRAM, 256KB NVRAM |
| Operating
System |
| |
Real-time,
preemptive multi-threaded/multitasking
kernel; FAT32 file system with long names;
supports SIMPL™ Windows® and SIMPL+™ |
| Connectors |
| |
COM
A - B |
(2) DB9
male;
(2) Bidirectional RS-232/422/485 ports;
Up to 115.2K baud;
Hardware and software handshaking support;
All ports support C2N-NPA8
Network Poll Accelerator |
| |
IR
SERIAL OUT A - D |
(4) 2-pin
3.5mm detachable terminal blocks;
(4) IR/Serial output ports;
IR output up to 1.2 MHz;
1-way serial TTL/RS-232 (0-5V) up to
115.2K baud;
Individual signal generator per port,
allowing simultaneous firing of all ports
Crestron MP2 Mp2E Control System |
| |
I/O
Versiports 1 - 4 |
(1) 5-pin
3.5mm detachable terminal block;
(4) Digital input/output or analog input
ports (referenced to GND);
Digital Input: Rated for 0-24VDC; input
impedance 20K ohms; logic threshold
1.24VDC;
Digital Output: 250mA sync from maximum
24VDC, catch diodes for use with “real
world” loads;
Analog Input: Rated for 0-10VDC, protected
to 24VDC maximum; input impedance 20K
ohms;
Programmable 5V, 2K ohms pull-up resistor
per pin |
| |
RELAY
OUT 1 - 4 |
(1) 8-pin
3.5mm detachable terminal block;
(4) Normally open, isolated relays;
Rated 1A, 30V AC/DC;
MOV arc suppression across contacts
Crestron MP2 Mp2E Control System |
| |
IR
IN |
(1) 3-pin
3.5mm detachable terminal block;
For connection of the CNXRMIRD
IR detector;
Allows IR wireless control from
third-party universal remotes loaded with
RC-5 IR commands |
| |
VIDEO
IN 1 - 4 |
(4) BNC
female;
(4) Composite [or (2) S-Video] inputs;
75 ohms terminated;
Discrete video sync detection |
| |
VIDEO
OUT 1 - 2 |
(2) BNC
female;
(2) Composite [or (1) S-Video] outputs;
Designed to drive 75 ohm loads |
| |
AUDIO
IN 1 - 2 |
(2) 5-pin
3.5mm detachable terminal blocks;
(2) Balanced/unbalanced stereo line-level
inputs;
Input Impedance: 15k ohms balanced, 10k
ohms unbalanced;
Maximum Input Level: 4 Vrms balanced, 2
Vrms unbalanced |
| |
AUDIO
IN 3 - 7 |
(5) 3-pin
3.5mm detachable terminal blocks;
(5) Unbalanced stereo line-level inputs;
Input Impedance: 10k ohms;
Maximum Input Level: 2 Vrms |
| |
AUDIO
OUT L/R |
(1) 5-pin
3.5mm detachable terminal block;
Balanced/unbalanced stereo line-level
output;
Output Impedance: 200 ohms balanced, 100
ohms unbalanced;
Maximum Output Level: 3.6 Vrms balanced,
1.8 Vrms unbalanced
Crestron MP2 Mp2E Control System |
| |
COMPUTER |
(1) DB9
female;
RS-232 computer console port |
| |
NET |
(1) 4-pin
3.5mm detachable terminal block;
Cresnet port, Master/Slave selectable;
Expandable via C2N-NPA8
Network Poll Accelerator |
| |
24VDC |
(1) 24
Volt DC power jack (PW-2410RU power supply
included);
Passes through to NET port to power
Cresnet devices via internal 2 Amp
self-resetting fuse |
| Video
Switcher |
| |
4x2
composite matrix switcher or 2x1 Y/C
(S-Video) switcher |
| |
Crosstalk |
-60dB
|
7x1
Stereo Audio Switcher and Equalizer
Crestron MP2 Mp2E Control System |
| |
Master
Volume |
-80dB to
+20dB, 0.1dB steps (balanced I/O) |
| |
Input
Compensation |
±10dB
per input channel |
| |
Bass/Treble
Gain Range |
±15dB,
0.5dB steps |
| |
Equalization
Modes |
5-band
graphic plus 1-band parametric;
speech-optimized 5-band graphic plus
1-band parametric; 3-band graphic plus
3-band parametric; or 6-band parametric |
| |
PEQ Filter
Gain |
±12dB,
0.1 dB steps from DMT; +24/-36dB, 0.1 dB
steps from SIMPL |
| |
PEQ Filter
Bandwidth |
.02 to
2.0 octaves (1.0 to 3.0 for shelving) |
| |
PEQ Filter
Center Frequency |
25Hz to
19.9kHz from DMT; 5Hz to 24KHz from SIMPL |
| |
PEQ Filter
Types |
low pass,
high pass, EQ filter (peaking/notching),
bass shelf, and treble shelf |
| |
GEQ Filter
Gain |
+5/-10dB,
0.1dB steps from DMT; ±10dB, 0.1dB steps
from SIMPL |
| |
Frequency
Response |
+0/-0.5
dB 20Hz to 20kHz |
| |
THD + Noise |
<0.005%
at 1kHz, 20Hz–20kHz A-weighted, max I/O |
| |
S/N Ratio |
>97
dB, 20Hz to 20 kHz A-weighted |
| |
Channel
Separation |
>100dB
at 1kHz, 90dB 20 Hz to 20kHz |
| |
Crosstalk |
>
-90dB 20Hz to 20kHz |
| |
Common Mode
Rejection |
>85dB
20Hz to 20kHz |
| Reset
Buttons - Crestron MP2 Mp2E Control
System |
| |
HW-R |
Hardware
reset (reboots the control system) |
| |
SW-R |
Software
reset (reloads the SIMPL program) |
| LED
Indicators |
| |
PWR, NET,
ERR |
(See
product manual for more information) |
| Power
Requirements |
| |
18
Watts (0.75 Amps @ 24 Volts DC);
PW-2410RU*
power supply included;
Available Cresnet Power: 7 Watts |
| |
*A
PW-2420RU
(sold separately) may be substituted,
providing a total of 30 Watts available
Cresnet power |
| |
Cresnet
Power Usage |
18 Watts
(0.75 Amp @ 24 Volts DC);
MP2 may be powered via Cresnet (with no
power supply connected to the 24VDC
connector) |
| Environmental |
| |
Temperature |
41° to
113°F (5° to 45°C) |
| |
Humidity |
10% to
90% RH (non-condensing) |
| Enclosure |
| |
Black
metal, 1U 19” rack mountable (rack ears
included) |
| Dimensions
- Crestron MP2 Mp2E Control System |
| |
Height |
1.7 in
(4.32 cm) |
| |
Width |
19.0 in
(48.26 cm) with ears; 17.03 in (43.24 cm)
without ears |
| |
Depth |
8.5 in
(21.59 cm) |
| Weight |
| |
3.54
lbs (1.59 kg) |
