|
|
Crestron
Remote Control Systems

Crestron
AV2 Dual Bus Remote Control System
|
Economical
Dual Bus Control Systems
|
|
The
Crestron AV2 dual bus control system is a completely new solution-driven control
technology that's also a network information control
system. It's the budget-conscious solution for even the
most complex control applications like media help desks,
videoconferencing, distance learning, and entertainment
facilities.
At
the heart of the Crestron
AV2 dual bus control system is the breakthrough 2-Series
Control Engine, based on the hot new 257 MIPS, 32-bit
Motorola ColdFire® processor. Onboard 34MB memory is
enhanced with a 4GB expansion slot that supports
off-the-shelf Type II compact flash memory and the IBM
Microdrive® hard disk drive, for on-board storage of
program and touchpanel files, room and equipment
profiles, upgrades, databases and schedules.
Crestron's
unique Dual Bus system, with its high-speed I/O bus
architecture, provides blazing fast throughput, system
wide. This Dual Bus architecture also lets you upgrade
to new, higher performance expansion cards, while still
using your existing cards and software pro-grams. The
40Mb/s Y-Bus supports existing CNX control cards and
serves as the pipeline for IR, serial communications and
relays. And the 300Mb/s Z-Bus is designed for super high
speed control card applications such as 10/100 Ethernet,
and future USB, USBII, FireWire, disk drive arrays and
more.
The
Crestron
AV2 dual bus control system also provides true secure network communications
required for today's corporate networks and the Internet
with a variety of plug-in 10/100 Ethernet cards. Using
the dual port Ethernet card, a built-in Firewall
delivers the ultimate in security, with on-board Network
Address Translator (NAT) and Router functions. It
supports static IP addressing and full duplex TCP/IP and
UDP/IP, and offers a WAN port for Internet and
Corporate-wide communications and a LAN port for Room
and AV Private Network use. And the built-in Web Server
provides the ultimate in help desk functions, and uses
memory storage on a compact flash card for remote access
and control.
The
2-Series real-time operating system is vastly upgraded,
yet compatible with existing Crestron software and
programming. A key feature is the Crestron Compiler,
which allows any existing Crestron SIMPL™ Windows®
control program to be easily recompiled for the
2-Series. The real-time, preemptive
multi-tasking/multi-threaded operating system offers a
FAT32 file system with long file names for easy and open
file management. And the enhanced SIMPL+™ instruction
set is also fully compatible with existing Crestron
SIMPL™ Windows® and SIMPL+™ programs.
With
its blinding speed, massive memory and revolutionary
Dual Bus architecture, the AV2 is built from the ground
up for high performance, secure Internet communications
and Dynamic Expansion Capabilities. Designed for
reliability and reinforced by Crestron's True Blue
Customer Support, it's part of the complete Crestron
line of advanced solutions for audio/video/Internet
distribution and control.
|
|
Crestron
AV2 Dual Bus Remote Control System

| Processor
- Crestron AV2 Dual Bus Remote Control System |
| |
CPU |
32-bit
Motorola 5407 ColdFire® Processor |
| |
Processing
Speed |
257
MIPS (Dhrystone 2.1 benchmark) |
| Memory |
| |
On-board
Memory |
36MB |
| |
Expandable
Memory |
Compact
Flash slot up to 4GB (accepts standard Type II
Compact Flash or IBM Microdrive® not included) |
| Y-Bus |
| |
40
Mb/s parallel communications; optional 3-slot
card cage supports Crestron's existing CNX
expansion cards and new C2 expansion cards |
| |
IR/Serial
ports |
8
programmable simultaneous outputs for IR, TTL
Level RS-232 or serial interface; signal (ws)
and ground (G) pins; infrared output up to
1.2MHz with individual VART per port allowing
simultaneous firing of all ports |
| |
I/O
Versiports |
(8)
programmable digital/analog input and
digitaloutputs; digital outputs offer 250mA sync
from maximum 24VDC; catchdiodes for use with
real world loads; digital inputs rated for
0-24VDC, 20K ohms input impedance, logic
threshold 1.25VDC; analog inputsrated 0-10VDC,
protected to 24VDC maximum, 20K ohms input
impedance; programmable 2K ohms pullup resistor
(per pin, software reference to GND or closure
to GND) |
| |
Communication
ports |
6
bi-directional ports for RS-232/422/485; Ports
3-6 Cresnet Accelerator ready |
| |
Computer
console |
1
RS-232 port (accessible from front or rear
panel), 9-pin DB9 for programming with a PC |
| |
Cresnet
port |
1
4-pin male connector, expandable via Cresnet
Accelerator, which increases the effective
network speed, fan-out and device addresses by a
factor of 8 for each poll accelerator added to
the system. |
| |
Relay
ports |
(8)
normally open, isolated relays; each relay is
rated 1A, 30VAC/DC; MOV arc suppression across
contacts for use with "real world"
loads |
| Z-Bus
Crestron AV2 Dual Bus Remote Control System |
| |
300Mb/s
parallel communications; 1 expansion card slot.
Optional cards include: C2ENET-1: Single Port
10/100 BaseT Ethernet, C2ENET-2: Dual Port
WAN-LAN-10/100 BaseT Ethernet. Future Support
for USB, USBII, FireWire. |
| |
Ethernet
Support |
10/100
BaseT Ethernet, Dynamic/static IP and full
duplex TCP/IP, UDP/IP, Built-in Firewall, Built-inRouter,
Built-in Network Address Translator (NAT),
Built-in Web Server: Files shared in internal
flash or compact flash card memory (capabilities
depending upon which Z-Bus card is installed) |
| Operating
System |
| |
Real-time,
preemptive, multitasking kernel, Multi-threaded,
FAT32 file system with long names, Fully
compatible with existing SIMPL™ Windows® and
SIMPL+™ programs, Enhanced SIMPL+ instruction
set |
| Reset
Buttons |
| |
HW-R |
Performs
physical reset of system |
| |
SW-R |
Restarts
SIMPL program |
| LED
Indicators |
| |
PWR |
Indicates
power supplied to the unit |
| |
NET |
Indicates
activity within the system |
| |
ERR |
Indicates
an error message is available from the software
feature buttons |
| |
LNK
A |
Indicates
attachment to LAN (port 1 of Z-Bus card) |
| |
ACT
A |
Indicates
communication over LAN (port 1 of Z-Bus card) |
| |
LNK
B |
Indicates
attachment to LAN (port 2 of Z-Bus card, if dual
port card inserted) |
| |
ACT
B |
Indicates
communication over LAN (port 2 of Z-Bus card, if
dual port card inserted) |
| Power
Requirements -
Crestron AV2 Dual Bus Remote Control System
|
| |
100-250VAC,
2.3A, 50/60Hz, internal universal power supply.
Depending on the expansion slot load, there is a
50W maximum load rating |
| Dimensions |
| |
3.47"
/ 8.81cm (H) x
19.00" / 48.26cm (W) x
9.7" / 24.6cm (D) |
| Weight |
| |
6.75lb
(3.1kg) |
| Optional
Accessories |
| |
CAGE2 |
3
Card expansion cage |
| |
C2N-NPA8 |
Allows
a large number of Cresnet devices to be
controlled by a single AV2 while maintaining a
high level of reliability and performance.
Connecting to the control processor via a
high-speed RS-232 (using built-in COM ports 3-6)
or Ethernet link, it effectively multiplies
Cresnet bandwidth by implementing eight
simultaneous Cresnet networks, each operating at
full speed. Multiple units can be used at the
same time for even larger or faster systems. |
| |
C2ENET-1 |
Single
port ethernet card |
| |
C2ENET-2 |
Dual
port ethernet card |
|
|
|
Call
Toll-Free 8:00-5:00 CST Mon-Fri
Audio
Visual Technologies Group
4910
Wright Rd #100
Stafford, TX 77477
www.avtg.com
|